Used Boss washing machines in Islamabad & Rawalpindi
Is a used Boss washing machine worth buying?
Boss is a Lahore manufacturer whose range runs well past laundry — gas water heaters, cookers, water dispensers — so the dealer selling the machine usually carries its parts as well. The washing machines are KE-coded, mechanical, and built from parts cheap enough that these get patched rather than retired. What you are really assessing is how the patching was done.
Made or assembled in Pakistan
Spares are widely stocked locally and most technicians in the twin cities have worked on these, so common faults are usually economic to repair.
Boss spares are ordinary shelf stock across both cities — motors, timers, belts, pulsators, drain valves and lid switches — and the same dealers who sell Boss water heaters and dispensers carry them. Anything less common is ordered against the KE code.
Washing Machines in stock now
Our current washing machines, across all brands — ask us on WhatsApp if you want Boss specifically.
NewAutomatic Haier Washing Machine 7 kg, 8 kg Brand New
Good UsedAsia
Good UsedDawlance DWT-250C TangleFree fully automatic top-load washing machine
For Parts / RepairSamsung washing machine
Checking a used Boss washing machine
These are specific to Boss. The general washing machines checks apply too and are on the washing machines page.
Find the KE code
Boss washing machines carry short KE-prefixed model codes on the plate. Boss dealers stock by that code and independent shops stock the same parts generically, so a legible code gives the machine two supply routes instead of one.
Check the pulsator sits flush
Lift the lid and turn the pulsator by hand: it should sit flat in the tub floor and turn without rubbing. Because Boss pulsators are cheap shelf parts they get replaced casually, and one fitted proud or off-centre grinds against the tub floor until it wears through.
Do a run-down test
Switch the spinner off at speed and watch it coast. It should slow smoothly and stop; a basket that stops abruptly is dragging on the brake, one that rumbles louder as it slows is the bearing. Both are stocked parts on a Boss, so price them in rather than walk away.
Run both halves together
Fill the wash tub and run the wash and spin sides at once. A twin tub shares one mains lead and one loom between two motors, and a bad joint or scorched terminal block usually only shows itself under both loads — which is where a cheap past repair on these machines announces itself.
What Boss washing machines are worth
- Boss parts are cheap enough that faults tend to be fixed before a sale rather than disclosed, so value follows the quality of the repairs — matched parts, a tidy loom — rather than whether the machine has ever been repaired at all.
- A Boss twin tub with both halves working is worth more than the two halves separately, because a buyer at this level wants one machine that washes and spins and will not pay twice for the floor space.
- A legible KE code gives the machine two parts routes, Boss dealers and independent shops; a plate washed off by damp leaves only what a shop can fit by eye, and that narrowing shows up in the offer.
Model lines you will see second-hand
- KE-series twin tubs
- KE-series single-tub washers
- Boss spin dryers
General washing machines checks
These apply whatever the badge on the front says — the washing machines page covers them in full.
Spin the empty drum
With the machine off, turn the drum through a full rotation by hand. It should move smoothly and quietly. A rumble, a grinding note or side-to-side play means worn drum bearings, and on most front loaders the tub has to come apart to reach them, which rarely makes sense on a used machine.
Run a cycle with water
Ask for a rinse-and-spin with the machine actually filling. Watch that it takes water at a reasonable rate, drains fully, and reaches full spin without walking across the floor. Slow filling is usually a clogged inlet filter; refusing to spin with a wet load is often a worn belt, coupler or motor.
Fold back the door seal
On a front loader, peel the rubber boot back all the way round. Black mould in the folds is cleanable. Tears, splits or a seal that has been patched with adhesive are not, and a compromised boot leaks onto the floor at every wash.
Test the spinner separately
On a semi-automatic, the spin tub has its own motor and a lid interlock. Load it with a wet cloth and run it. Heavy vibration, a screech at start-up, or a spinner that keeps turning with the lid open are all faults, and the last one is a safety problem rather than an inconvenience.
Open the pump filter
Undo the filter at the front and look at what comes out. Grit and hair are normal. A cracked filter housing, or a drain hose with a taped repair, tells you the machine has been leaking, and water stains under the base panel are worth more than any verbal assurance.
Step through the programmes
Select each programme and confirm the machine changes what it actually does, not just what the display shows. An error code that clears when the machine is unplugged and returns mid-cycle points at the control board, which is the second expensive repair after bearings.
Boss washing machines — questions
How can I tell if a used Boss washing machine has been badly repaired?
What should I do before selling a used Boss washing machine?
Other washing machines brands
Selling one instead? We buy used Boss washing machines for cash.